Showing posts with label Scale. Show all posts
Showing posts with label Scale. Show all posts

Tuesday, 10 February 2015

The Tricky bit

The Tricky Bit


When we left off we had our boat in plan and profile. The job now is to see if those lines will match up in the third dimension and still have fair curves. This is done by drawing the sections.

In the cartoon the sections are drawn in the middle of the drawing about station 5 which is used to represent the centreline (CL). You can in fact draw it any where, the reason I chose that particular position was that I was doing this without most of the tools and no drawing board. So to lay off the sections I was using tick strips. You can read more about this method here (http://www.lackeysailing.com/daysailor/sidebars/tickstrip.htm)

In that application the person is using a large piece of wood as he is doing it full size, however you can use strips of paper to do the same thing on your scale drawing. In order to do this you must first draw in a waterline (WL) where you are going to put your sections drawing, in this case I put it mid way between the profile drawing and the plan.

In the following picture a small slip of paper is laid along Station 5 and ticks are made at the WL, the chine (the curve of he bottom) and the sheer.



This then transferred to the new WL and CL by lining the strip along the CL with the WL tick at the WL. Then the strip is laid out on the plan to take off the widths and the widths laid out in the same way along the WL. Lines are drawn from the ticks parallel to the WL and CL and where they intersect are the sheer and chine points. You draw lines through those points and you have a section. This is time consuming and prone to error.



There is another way. To the right, or if you prefer left, of the drawing extend the WL and draw an new CL perpendicular to the WL. Extend the plan CL to intersect with the new CL and from that intersection draw two 45 degree angles.




Then using your triangles transfer the plan and profile measurements. First the plan,



You will probably have to extend the line of the second triangle using a ruler, make a tick mark on the diagonal slide your triangle down and do the same for the chine line in plan.

Then slide your triangle along the yard stick and draw two perpendicular lines through the marks.


Now go to the profile and draw Two lines parallel to the WL from station 5 at the sheer and chine.




Join the intersections, erase all the unneeded lines and you have the half section at station 5.



Now do that for all the other stations with stations 0 to 5 on one side of the CL and 6 to 10 on the other. Draw a line parallel to the baseline from the bow to the CL. You end up with this,



And now for the tricky bit. Join the ends of the section lines at the chine and at the sheer to see if you have a fair curve. In most instances, when drawing by hand, you won't on the first try and will have to alter the lines in plan and profile to make the curves fall fair. That can be exceedingly time consuming.

Once that's done you have this,



In this case the curves fell fair on the first go and there is a reason for that, we'll discuss that next time.

Monday, 2 February 2015

More tools of the trade

More tools of the trade


In the last post I said to make a line parallel to the yardstick 6” up, that was six real world inches not scale inches and the same for the center line. All other measurements were to scale 1/2”=1'. In this post all measurements are scale unless otherwise specified.

We ended the last post with the following grid,

On this grid we will construct the lines in plan using the centerline (CL) marked in red and in profile using the waterline (WL) in green. From the cartoon we know that the proposed draft is 6”, and it appears halfway between station 5 and station 4. Measure down from the waterline 1' on stations 4 & 5. Draw a line from the intersection of the WL and station 4 to the mark on station 5 and vice versa, that will establish the point of maximum draft thusly.



Now we need to construct a fair curve from the intersection of Station 10 and WL through the point of maximum draft to the intersection of station 0 and WL.

This brings into play new tools, french curves, ship curves and splines and ducks otherwise known as spline weights. The basic drafting set contains french curves but in order to get long fair curves you really need ship curves or a spline and ducks.

A spline is a narrow sectional piece of wood or plastic which can be bent through several points to construct a curve. The spline is held in place by lead ducks,



These things are hard to find and when you do find them they are expensive. When I was doing the Westlawn course I carved two male molds and took then to a local foundry and had them cast ten for me which was way cheaper than trying to buy them, Or you can try to make them yourself, there is a good article at Duckworks on how to do this. (http://www.duckworksmagazine.com/06/howto/splineweights/index.htm)

Once you have all your ducks in a row then you can use the spline to draw the curve of the bottom.



And then remove the X from between stations 4 and 5. Which brings up another tool the eraser, get a good one you'll be using it a lot and you'll also need an eraser shield to protect the parts of your drawing you don't want erased and a drafting brush to sweep all the eraser bits off the drawing so it doesn't smudge.

Once the bottom curve is drawn turn your attention to the bow and stern. From the cartoon we know that the top of the transom is 1' aft of station 10 and 2' above WL, using dividers mark out those points.

Problem! The cartoon length over all (LOA) is 17' but we only want 16'. If we whack 1' off the LOA will we still get the sheer (the curve of the gunwale in profile) that we wanted? The only way to find out is to draw it in and look at it. So, again using the dividers, mark out a point forward of station 0 3' up from WL and 2' forward of station 0. Then draw a line from the mark aft of station 10 to the intersection of station 10 and WL. Do the same at the bow.



From the cartoon we know that the sheer is at it's lowest point at station 7, 1' 9” above WL so using the spline and ducks we'll construct a curve from the bow to the stern through that point on station 7.



Now take a good look at that line from all directions, is it fair, does it look good. I think so, in fact I think it looks better than the cartoon. So 16' is good.

Using the same process of taking measurements off the cartoon and using our spline and ducks we can draw in the sheer and bottom line in plan.



So far so good but the real test of all this will come when you draw the lines in section like the center portion of the cartoon. We'll discuss that next time.